research centers


Search results: Found 2

Listing 1 - 2 of 2
Sort by

Article
Effect of Annealing Treatment on the Anisotropy Behavior of Cold Rolled Stainless Steel 304 Sheets

Authors: Ahmed A. Zainulabdeen احمد عميد زين العابدين --- Jabbar H. Mohmmed --- Najmuldeen Y. Mahmood
Journal: DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية ISSN: 19998716/26166909 Year: 2018 Volume: 11 Issue: 2 Pages: 84-89
Publisher: Diyala University جامعة ديالى

Loading...
Loading...
Abstract

Anisotropy of materials has harmful effects during deep drawing operations and reduce it will strongly enhance the productivity and quality of deep drawing yields. In this work the effect of annealing treatment on texture and anisotropy behavior of cold rolled stainless steel 304 sheets were investigated. Uniaxial tensile test samples cut at 0o, 45o and 90o to the rolling direction were prepared in order to measure the anisotropy parameters (normal anisotropy, r_n, and planar anisotropy, ∆r). Two annealing temperatures (1050, and 1150) °C were used to study their effects on anisotropy behavior. The results show that the normal anisotropy value of annealed samples at 1150°C increases by (31%) as compared to the received samples. This indicates that the annealed samples at 1150 °C have the highest formability. Also, results show significant reduction (about 88.7%) in planar anisotropy value for 1150°C annealed samples. This gave rise to an increase in deep drawing yield.


Article
An Experimental Approach and Constructing a New Non-Linear Regression Model for Prediction the Anisotropy Parameters of Annealing Treated Commercially Pure Aluminum Sheets

Authors: Jabbar H. Mohmmed --- Ali A. Mohsen --- Bassam A. Ahmed --- Najmuldeen Yousif Mahmood
Journal: Engineering and Technology Journal مجلة الهندسة والتكنولوجيا ISSN: 16816900 24120758 Year: 2016 Volume: 34 Issue: 14 Part (A) Engineering Pages: 2775-2783
Publisher: University of Technology الجامعة التكنولوجية

Loading...
Loading...
Abstract

Earing is a common phenomenon in deep drawing process that increases the waste of metal. This phenomena is affected by material anisotropy, thus, it is important to study the effects of material parameters on this material behavior. This paper focuses on identify the optimal condition of annealing treatment which result in higher value of normal anisotropy and lower value of planar anisotropy which lead to reduce the waste material in subsequent forming processes. Therefore, in this study, anisotropic behavior and formability of commercially pure aluminum thin sheets was investigated after annealing the samples at different temperatures (350, 400, and 450) °C. Uniaxial tensile tests were carried out at room temperature (25°C) to evaluate formability parameters. For this purpose different tensile test samples in the directions of 0°, 45° and 90° in respect to the rolling direction were prepared. In addition to, metallographic test was carried out to as-received and annealed samples to observe the changes in microstructure. Plastic strain ratio and planar anisotropy of samples were calculated from the tensile test data. Based on the tensile test results of samples, the earing phenomenon due to planar anisotropy in commercially pure aluminum sheet was analyzed. The results indicate that the annealing at 400°C brought the optimum conditions.Moreover, new regressions model for prediction the anisotropy parameters of sheet metal using statistical techniques (SPSS software) were constructed in this work. The experimental data were compared to those predicting values. A comparison clearly indicates that there are good identification between measured and predicted values with multiple correlation coefficients R of 0.932 and accuracy of about 87 %. The results reveal that the proposed model is effective and reliable tool to obtain accurate prediction of the anisotropy behavior of metal sheets.

Listing 1 - 2 of 2
Sort by
Narrow your search

Resource type

article (2)


Language

English (2)


Year
From To Submit

2018 (1)

2016 (1)